Questions? 1-800-442-2581
or 1-616-784-1121
8:00am-5:00pm M-F (Eastern Time)
Share |
Air Circulator Fans
Air Doors/Air Curtains
Baseboard Space Heaters
Bathroom Fans
Blowers (Portable Utility)
Camp, Fish, Hunt & RV
Ceiling Fans (Commercial/Ind.)
Church Baptistry Heaters
Clearance & Specials
Comfort Space Heaters
Construction Heaters
Controls & Transformers
Drum Blowers (Portable)
Evaporative Coolers
Floor Warming Mats/Cables
Garage & Shop Heaters
Garden & Outdoor Items
Hand Dryers (Washrooms)
Heaters & Accessories
Heating Cable & Mats
High Temperature Insulation
High Temp. Wire & Acces.
Industrial Heating Products
Infrared Radiant Heaters
Lighting & Flashlights
Loading Dock Fans
Manufacturers (Vendors)
Nichrome Wire Coils & Acc.
Patio Heaters (Radiant)
Pipe Trace Freeze Protection
Portable 120V Space Heaters
Portable 240V Space Heaters
Replacement Repair Parts
Roof & Attic Ventilators
Roof & Gutter Deicing Cable
Snow & Ice Removal
Tapes (Adhesive)
Temperature Sensors
Thermostats & Accessories
Tools, Glue, Lights & Gear
Unit Heaters (Blower)
Wall Exhaust Fans
Wall Heaters (Fan-forced)
Wall Panel Convectors
Water Heaters (Tankless)
Whole House Fans
Item Code: MARKEL645287

Description:  HF2B5110CA1L Markel Electric Unit Heater

Markel 5100 Series Electric Unit Heater - 208/240 Volt - 1 or 3 Phase - 7.5/10 KW - 24VAC Control Voltage - 24.3125"H x 21.5"W x 6.5"D


Typically in stock at vendor warehouse, call for delivery time

Tpi Corporation


Click Images to Enlarge



Voltage: 208/240 Volt
Phase: 1 or 3 Phase
Wattage: 7.5/10 KW
Applications: Room Heating
Warehouse Heating
Dimensions (HxWxD): 24.3125"H x 21.5"W x 6.5"D
Manufacturer: Markel
Included: Heating Unit

Features of Markel HF2B5110CA1L Electric Unit Heater

The Markel 5100 Series Horizontal or Vertical Mounted Electric Fan Forced Unit Heater is a commercial and Industrial grade unit heater.

CONSTRUCTION: Heavy 18 Gauge welded steel cabinet with powder coated finish and control compartment housing a master terminal board with a hinged and latched access door, simplifying wiring, installation and maintenance.

HEATING ELEMENT: Copper clad steel sheath element with continuously brazed steel fins formed to allow side draw through air flow.

OVERHEAT PROTECTION: All units come equipped with automatic reset type limit controls to de-energize the heater should an over-temperature situation occur.

FAN and MOTOR: Totally enclosed, 1-speed, 1-phase, permanently lubricated, thermally protected motors with unit bearings on 3 KW - 20 KW models. Totally enclosed, 2-speed, 1-phase, permanently lubricated, thermally protected motors with sleeve bearings on 25 KW - 50 KW models. All motors mounted with rubber insulators to minimize vibration & noise. Fan over-ride purges unit of residual heat at shutdown.

LOUVER ASSEMBLY: Louvers are individually adjustable for directional control of air flow up to 15 degrees from straight horizontal. Optional diffusers available for down flow (vertical discharge) applications.

TEMPERATURE CONTROLS: Optional low voltage and line voltage thermostats are available with an adjustable temperature range of 40F to 90F. Units with model numbers ending in CA1 are factory wired for low voltage controls. 25 KW through 50 KW units are designed for two stage heating operation.

The Markel 5100 Series Electric Unit Heaters (3.3KW thru 50KW) can be mounted for horizontal or vertical discharge.

Horizontal unit heaters are recommended in low bay areas with maximum 15 to 18 foot ceilings. These should be concentrated along outside wall or other areas of greatest heat loss; spaced to set up a generally circular air movement, each heater supporting the air stream of the other.