Questions? 1-800-442-2581
or 1-616-784-1121
8:00 am - 5:00 pm M-F EST
8:00 am - 1:00 pm Sat. EST
 
 
Share |
 
Refine Results Clear All
Product Types
Fan Forced Heaters
Unit Heaters
Voltage
208 Volt
240 Volt
Phase
1 Phase
Wattage
11.25 KW
7.5 KW
Price
$500 to $1000
Vendors
King Electric
Product Types
Select Product Types Clear
 Fan Forced Heaters (2)
 Unit Heaters (2)
Voltage
Select Voltage Clear
 208 Volt (1)
 240 Volt (1)
Phase
Select Phase Clear
 1 Phase (2)
Wattage
Select Wattage Clear
 11.25 KW (1)
 7.5 KW (1)
Price
Select Price Clear
 $500 to $1000 (2)
Vendors
Select Vendors Clear
 King Electric (2)
$25 or Less Products
Baseboard Space Heaters
Camp, Fish, Hunt & RV
Church Baptistry Heaters
Clearance & Specials
Comfort Space Heaters
Construction Heaters
Controls & Transformers
Cooling/Air Conditioning
Fans/Blowers/Ventilation
Floor Warming Mats/Cables
Garage & Shop Heaters
Garden & Outdoor Items
Hand Dryers (Washrooms)
Heaters & Accessories
Heating Cable & Mats
High Temp. Insulation
High Temp. Wire & Acces.
Industrial Heating Products
Infrared Radiant Heaters
Lighting & Flashlights
Manufacturers (Vendors)
Nichrome Wire Coils & Acc
Patio Heaters (Radiant)
Pipe Freeze Protection
Portable Space Heaters
Replacement Repair Parts
Roof & Gutter Deicing
Snow & Ice Removal
Tapes-Fiberglass/Aluminum
Temperature Sensors
Thermostats & Accessories
Tools, Instruments & Gear
Unit Heaters (Blower)
Wall Heaters (Fan-forced)
Wall Panel Convectors
Water Heaters (Tankless)
ITEM # QTY.
Results
You searched for: PKB Series 240V 1PH Portable Unit Heaters
Results Displayed: 1 - 2 of 2
This workhorse of a portable heater is typically used on jobsites where dry heat is needed in an otherwise moist location. Faster dry times are obtained by using electric instead of propane; therefore,
dry times are reduced by at least three times.

Dry heat and air movement are the keys to getting the job done right. Temporary heating is the other typical application that these heaters fill, using fewer heaters and providing temporary comfort in time of need. Low temperature rise and high airflow across the coils makes it ideal for dry out applications.




* Spiral Steel Fin Element
* Cast Iron Motor
* Aluminum Fan Blade
* Built-in Thermostat
* Heavy Gauge Steel Enclosure
* Adjustable Discharge Louvers
* Totally Enclosed Motor
* SO Cord (No Plug)
* Tip Over Switch
* Electro-Galvanized Construction
* Baked Enamel Finish
* Handle for Carrying


Construction: All exterior and interior metal enclosure parts are made from 20GA electro galvanized steel with a rust inhibiting baked enamel finish. Smooth rounded corners and protective edge trim give an attractive modern appearance.

Adjustable Outlet Louver: Louvers direct air up or down as needed for the heating application.

Rear Intake Screen: Heavy gauge steel screen protects against foreign objects making accidental contact with the rotating fan blade.

Spiral Fin Elements: The metal sheath element is brazed with spiral fins and then molded into a coil configuration. This combination produces the best heat transfer while eliminating the potential for hot spots by positioning the element in the maximum airflow stream.

Totally Enclosed Fan Motor: Permanently lubricated cast iron with 20 cc of oil. Epoxy coated motor with enclosed rotor resists moisture and corrosion for long lasting trouble free operation.

Aluminum Fan Blade: Axial flow type fan mounted directly to the motor shaft for maximum efficiency.

Auto-Reset Thermal Cutout: Power is disconnected from the element if an over heated condition occurs. The fan continues to run to dissipate excess heat from the element. The element is re-energized automatically when the normal operating temperature returns.

Internal Controls: Magnetic contactors are standard on the following models: 1) all 480V heaters, 2) all 208V-1Ø, 240V-1Ø, and 277V-1Ø heaters above 6-KW, 3) all 3Ø heaters. The control voltage is equal to the line voltage (208, 240 or 277) except for 480V models where a transformer is provided for 24V Control. Sub circuit fusing is provided when the heater ampacity exceeds 48 amps to comply with NEC standards. A fan delay is provided standard on models 12.5-KW and above to dissipate residual heat from the heating elements.














http://www.king-electric.com/PDF/PKB%2058-59.pdf
Item CodeDescriptionVendorQuantity
KINGELECTRIC16276
PKB2415-1 King Electric Unit Heater
King Electric Portable Unit Heater - PKB Series - 208 Volt 1 Phase 11.25KW or 240 Volt 1 Phase 15KW - 925 CFM - 51F Temperature Rise - 33ft Air Throw - Includes SO Cord But Does NOT Include A Plug - Tip Over Switch - Carrying Handle
King Electric
KINGELECTRIC16254
PKB2410-1 King Electric Unit Heater
King Electric Portable Unit Heater - PKB Series - 208 Volt 1 Phase 7.5KW or 240 Volt 1 Phase 10KW - 725 CFM - 44F Temperature Rise - 24ft Air Throw - Includes SO Cord But Does NOT Include A Plug - Tip Over Switch - Carrying Handle
King Electric